T850 Lens 3D Pad Printing Series
T850 Lens 3D Pad Printing Series
T850 Lens 3D Pad Printing Series is a professionally developed pad printing ink specifically designed for non-standard materials that are difficult to screen print. This series of inks not only has good transfer printing performance, but also has very high viscosity stability and extraordinary usage time. The cured film layer has good adhesion, various physical and chemical resistance.
Scope of application: Commonly used for physical tempered glass and chemical tempered glass.
Performance characteristics: Its significant advantages are manifested in excellent transfer printing performance; Simultaneously using environmentally friendly solvents, reducing irritating odors, and minimizing the frequency of oil cup replacement.
Technical Parameters：
|
Ink printing operation process |
Add 10% T850-MG900 curing agent and dilute it for screen printing with a mesh size of 350 to 420; First degree drying at 160 ℃ for 10 minutes/Second degree drying at 160 ℃ for 20 minutes |
||||
|
Test Project |
Test method |
test instrument |
Evaluation criteria |
Test results |
|
|
surface tension |
Guidelines for the Use of Dain Pen |
Full specification Dain pen |
Different products have varying levels of quality |
30-32 |
|
|
dimensional change |
Standard process of anime measuring instrument (165S/420 mesh printing) |
Anime measuring instrument |
≤ 4 wires (40 microns) |
2.6 filaments (26 microns) |
|
|
Ultrasonic washing |
Conventional detergent//65℃//2Hr |
Ultrasonic oscillator//Hundred grid knife//3M adhesive paper |
① No foaming; |
5B |
|
|
Water-resistant boiling |
Immerse in deionized water at 100 ℃2Hr |
water bath |
① No foaming; |
5B |
|
|
High and low temperature wet heat cycle |
80℃//95%RH(8Hr)//-20℃(2Hr)共10个循环 |
高低温湿热循环实验箱 |
① No foaming; |
OK |
|
|
hardness |
Mitsubishi pencil at a 45 degree angle/subjected to a force of 500 grams/tested 3 times at different locations |
Hardness tester Mitsubishi pencil |
≥3H |
3H |
|
|
adhesion |
Draw 100 grids/3M adhesive paper and pull it out 5 times in a row |
Baige knife//3M adhesive paper |
Hundred grid test 100% |
100% |
|
|
surface resistance |
Measure its surface resistance at 5 locations (≤ 80% RH) |
Surface resistance tester(FLUKE1508) |
≥1010ohm |
≥11Gohm |
|
|
acid-resistant |
Immerse in 25 ℃//5% dilute H2SO4 solution2Hr |
Thermostatic water bath//glassware |
① No foaming; |
OK |
|
|
Alkali resistant |
Immerse in 25 ℃//5% NaOH solution2Hr |
Thermostatic water bath//Stainless steel utensils |
① No foaming; |
OK |
|
|
Alcohol-resistant |
The testing machine is loaded with 200 grams of force and rubbed back and forth 100 times with cotton cloth dipped in 99% or more alcohol |
Low friction machine//cotton velvet fabric//alcohol |
① Not fading |
OK |
|
|
Solvent resistant |
The testing machine is loaded with 200 grams of force, and cotton fabric is dipped in chemically pure acetone and rubbed back and forth 50 times |
Low friction machine//cotton velvet fabric//butanone |
① Not fading |
OK |
|
Usage:
① Before use, please add the matching T850-MG900 curing agent and an appropriate amount of diluent in a ratio of 10%, and stir thoroughly before printing.
② The recommended baking temperature is 160 ℃ and the time is 10-20 minutes. Please confirm if other conditions are feasible first to avoid affecting the quality of the finished product.
③ When printing multiple layers, the first layer can be cured at 160 ℃ for 5-8 minutes, and the second layer can be cured at 160 ℃ for 20 minutes to ensure quality.
④ The selection and dosage of diluent depend entirely on the printing mesh size, environmental conditions, and printing effect.
Storage conditions: ① Before and after use, the ink container of this series should be completely sealed and stored in a cool and ventilated place, avoiding contact with open flames or high temperatures.
Copyright @ 2026 Guangdong Qihe Cai Ink Co., Ltd ICP Record Number：粤ICP备2022064656号
Scan the code to follow us
（Long press to recognize QR code）